[ Pobierz całość w formacie PDF ]

Top cover
PC Card door
Speaker grills
Monitor support cover slot buttons
Label
To remove the upper case assembly, follow these steps:
1. Prepare the ArmadaStation for disassembly (Section 5.3).
2. Position the ArmadaStation so the front is facing forward.
3. Remove the alignment tray assembly (Section 5.4).
4. Remove the rear panel assembly (Section 5.5).
5. Remove the three screws securing the upper case assembly to the base assembly
(Figure 5-11).
Figure 5-11. Removing the Upper Case Assembly Screws
ArmadaStation Removal and Replacement Procedures 5-11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. Grasp the back of the upper case assembly, lift up on the back of the assembly, and
swing it forward (Figure 5-12).
Figure 5-12. Removing the Upper Case Assembly
7. Set aside the upper case assembly.
5-12 ArmadaStation Removal and Replacement Procedures
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To install the upper case assembly, follow these steps.
1. Align the front edge of the upper case assembly with the front edge of the base
1
assembly (Figure 5-13).
2. Swing the back of the upper case assembly back and down until it rests on the base
2
assembly .
Figure 5-13. Installing the Upper Case Assembly
3. Replace the three upper case screws.
NOTE: When installing the upper case assembly, make sure the ribs on the center of
the base assembly are engaged in the slot in the front of the upper case assembly.
ArmadaStation Removal and Replacement Procedures 5-13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7 Drive Cage Shield
The drive cage shield is located in the base assembly and covers the half-height bay
assemblies. To remove the drive cage shield, follow these steps:
1. Prepare the ArmadaStation for disassembly (Section 5.3).
2. Remove the alignment tray assembly (Section 5.4).
3. Remove the rear panel assembly (Section 5.5).
4. Remove the upper case assembly (Section 5.6).
1
5. Remove the three screws securing the drive cage shield to the base assembly
(Figure 5-14).
2
6. Lift up on the front of the drive cage shield and pull forward to fully disengage .
Figure 5-14. Removing the Drive Cage Shield
7. Pull the drive cage shield forward until the shield clears the base assembly.
5-14 ArmadaStation Removal and Replacement Procedures
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To install the drive cage shield, follow these steps:
1
1. Align the tabs on the back of the shield with the slots in the backplane assembly
(Figure 5-15).
NOTE: Make sure any cables used to connect half-height drive assemblies are properly
tucked underneath the slots in the backplane cover and not resting on top of the drive
cages before installing the drive cage shield.
2
2. Swing the front of the shield down .
3
3. Install the three screws securing the shield to the base assembly . Note that the
middle screw is different in size and type from the other two screws.
4
NOTE: Make sure the screw installed on the right side of the drive cage shield
secures the control panel assembly ground strap to the drive cage shield.
Figure 5-15. Installing the Drive Cage Shield
ArmadaStation Removal and Replacement Procedures 5-15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8 Half-Height Bays
The ArmadaStation features one standard half-height bay, which is located on the front
of the ArmadaStation. This bay supports any standard half-height drive (such as a
diskette or hard drive) or a MultiBay (using a half-height MultiBay adapter).
A MultiBay comes as standard equipment in the ArmadaStation right half-height bay.
This allows you to use removable drives from the computer or charge battery packs.
To access the half-height bays, follow these steps:
1. Prepare the ArmadaStation for disassembly (Section 5.3).
2. Remove the alignment tray assembly (Section 5.4).
3. Remove the rear panel assembly (Section 5.5).
4. Remove the upper case assembly (Section 5.6).
5. Remove the drive cage shield (Section 5.7).
Once these steps have been completed, standard half-height drives and half-height
MultiBay adapters can be installed and removed.
Half-Height Drives
To remove a half-height drive from an ArmadaStation half-height bay, complete these
steps:
1. Remove the drive cage shield (Section 5.7).
2. Disconnect the cables attached to the half-height drive.
3. Lift the half-height drive out of the base assembly.
Reverse the removal procedure described above to reinstall a half-height drive.
If a half-height drive is being installed in the ArmadaStation left half-height bay for the
first time, complete these steps:
1. Remove the drive cage shield (Section 5.7).
2. Lift the drive cage out of the base assembly.
5-16 ArmadaStation Removal and Replacement Procedures
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. Remove the half-height bay blank bezel cover from the drive cage (Figure 5-16).
Figure 5-16. Removing the Half-Height Bay Blank Bezel Cover
ArmadaStation Removal and Replacement Procedures 5-17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. Remove the screws from the sides of the half-height drive (Figure 5-17).
NOTE: The half-height drive should have two screws installed in each side. If these
screws are missing, appropriate-sized screws must be obtained to secure the
half-height drive to the drive cage shield.
Figure 5-17. Removing the Half-Height Drive Screws
5-18 ArmadaStation Removal and Replacement Procedures
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Place the drive cage over the half-height drive. Align the front of the drive with the
tab on the front of the drive cage (Figure 5-18).
NOTE: The drive cage should be aligned so the  L and  LEFT indicators can be
read when the half-height drive is installed in the ArmadaStation left half-height bay.
Figure 5-18. Aligning the Half-Height Drive with the Drive Cage
ArmadaStation Removal and Replacement Procedures 5-19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. Install the screws securing the half-height drive to the drive cage (Figure 5-19).
Figure 5-19. Installing the Half-Height Drive Screws
5-20 ArmadaStation Removal and Replacement Procedures
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [ Pobierz całość w formacie PDF ]